C5.1a To explain
how the concentration of a solution in mol/dm3 is related to the mass of the solute
and the volume of the solution by making standard solutions.
How to make a standard solution.
First
thing you have to do is decide whether it's a primary standard or a secondary
standard you need to make up.
Primary Standards
Primary
standards are used to determine the concentration of other less stable reagents
used in volumetric analysis.
Compounds
used to make primary standard solutions have therefore to have certain
properties.
Features of a primary standard:
• Unreactive
except with the reagent they standardise.
• Low
hygroscopicity i.e. they don’t absorb water vapour from the air on standing for
a long time on the prep–room shelf.
• High
molar mass to reduce errors in weighing and calculations.
• Can be
obtained in a very pure form.
• Preferably
non–toxic.
• Obviously
soluble in water.
• Lastly
if possible they need to be cheap and readily available.
The
primary standard used to standardise alkaline solutions such as sodium
hydroxide is solid potassium hydrogen phthalate (C8H5O4K).
Sodium
carbonate solid (Na2CO3) is used to standardise acidic
solutions such as hydrochloric acid.
Once the
sodium hydroxide solution or hydrochloric acid solution has been standardised
it becomes a secondary standard.
An
important reason to standardise sodium hydroxide solution is to do with the
stability of these solutions.
You’ll
have seen this I think. If left for any
length of time in the lab or prep room, sodium hydroxide solution reacts with
carbon dioxide in the air. It forms
sodium carbonate in the solution and you can often see this because it looks
like flakes or a white solid in the bottom of the sodium hydroxide bottle.
2NaOH(aq) +
CO2(g) ⟶ Na2CO3(s) + H2O(l)
So let’s
suppose you need to make a 0.1M standard solution of sodium carbonate.
You have
available a 250ml volumetric flask, an electronic balance weighing preferably
to 3 decimal places and a supply of distilled water. Here’s what you can do:
First
calculate the mass of sodium carbonate you need to weigh out to make 250ml of
the 0.1M sodium carbonate solution.
First,
work out the molar mass of anhydrous Na2CO3: its 106
g/mol.
So a 1M
solution contains 106g of sodium carbonate therefore to find what a 0.15M
solution contains use:
so
so
But there
are only 250ml or a quarter of a litre in the flask so we need to weigh out 15.9g/4
or 3.975g of sodium carbonate.
Second, transfer
this mass of sodium carbonate into a weighing bottle weighing it to the nearest
0.001g.
Third,
put 50ml distilled water in a 250ml beaker and carefully transfer the bulk of
the sodium carbonate from the weighing bottle into the beaker.
Fourth,
reweigh the weighing bottle.
Fifth,
stir to dissolve the solid adding more water if needed.
Sixth,
transfer the solution to the volumetric flask through the filter funnel. Rinse the beaker well and make sure all the
liquid goes into the flask.
Seventh,
make the solution in the flask up to the mark using a dropping pipette.
Lastly,
shake the flask thoroughly several times to mix the contents completely.
Possible Errors:
1. Not
making up to the mark:
If you do
not add sufficient water and make the solution up to the mark then the
concentration of the solution will be higher than you expected it to be. You will have less water than expected.
2.
Spilling some of the solid in making the transfer:
If you
spill some of the solid then the solution contains less solid than expected so
its concentration is lower than expected.
Another
approach to the calculation of the mass of solute:
If
concentration is 0.15M then use
to
calculate the number of moles of solute required so
Knowing
the number of moles use
to
calculate the mass of solute required so
so
You’ll
read about how to carry out a titration in my next post.
No comments:
Post a Comment